125x125mm Welded Masonry Joist Hanger
125x125mm Welded Masonry Joist Hanger
Price: £4.50 (£5.40 inc VAT)
- Product Code: A1-5137
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model: WM125x125
- Weight: 890.00g
125x125mm Welded Masonry Joist Hanger
Width: 125mm
Height: 125mm
Weight: 890g
125mm x 125mm Welded Masonry Joist Hanger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. It is also suitable for many timber to timber and for timber to steel applications. The masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 125x125mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model: TRS1200B100
Delivery Time: In stock, 1-2 days
1200mm bent 100mm Ron Sammons strap is a lightweight restraint strap that can be used instead of a traditional Heavy Duty Strap to provide lateral restraint of roof trusses, rafters and joists tied to masonry and for vertical applications such as holding down the wall plate. Designed to Th..
£2.18
£2.62 inc VAT
Brand: TECO
Model: HD900B100
Delivery Time: In stock, 1-2 days
Galvanised Heavy Duty Restraint Strap 900mm Bent 100mm is designed for lateral and horizontal restraint (as in roof trusses). The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres holes.APPL..
£2.55
£3.06 inc VAT
Brand: TECO
Model: LD250F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 250mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres hol..
£0.61
£0.73 inc VAT
Brand: TECO
Model: FHM47/200
Delivery Time: In stock, 1-2 days
47mm x 200mm Single Piece Joist Hanger are designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. They are also suitable for many timber to timber applications by fixing the masonry flange securely to the timber or to steel beams using ap..
£2.41
£2.89 inc VAT
Brand: TECO
Model: PBPS15/17
Delivery Time: In stock, 1-2 days
Plaster depth 15-17mm uPVC Plaster Stop Beads are designed for use externally where galvanised bead cannot be used or where they are preferred to stainless steel. They are also used internally in high moisture content areas or where pro longed drying out periods may be necessary. An impact..
£3.56
£4.27 inc VAT
Brand: TECO
Model: TCSS 76mm M12
Delivery Time: In stock, 1-2 days
Diameter: 76mmTeeth Size: 1.2mm76mm M12 Single Sided Tooth Plate Timber Connectoris designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are produce..
£1.16
£1.39 inc VAT