75x250mm Welded Masonry Joist Hanger
75x250mm Welded Masonry Joist Hanger
Price: £5.50 (£6.60 inc VAT)
- Product Code: A1-5118
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model: WM75x250
- Weight: 779.00g
75x250mm Welded Masonry Joist Hanger
Width: 75mm
Height: 250mm
Weight: 779g
75mm x 250mm Welded Masonry Joist Hanger is designed to support 250mm high timber joist. The joist hanger's actual height is 240mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber and timber to steel applications, where masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 75x250mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model: STUDBZPM6
Delivery Time: In stock, 1-2 days
M6 Bright Zinc Plated Studding ( threaded bar), suitable for many applications. Supplied as standard in mild steel, high tensile available to order. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not use galvanised nuts & washers with stai..
£1.66
£1.99 inc VAT
Brand: TECO
Model: WSQPBZPM16
Delivery Time: In stock, 1-2 days
M16 Bright Zinc plated Square Plate Washers are made from heavy duty hot dipped spun galvanised steel. Suitable for a variety of applications where a heavy washer is required. Thickness 3mm. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not u..
£17.50
£21.00 inc VAT
Brand: TECO
Model: TCSS 63mm M12 SS
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mmSingle Sided Stainless Steel Tooth Plate Timber Connector 63mm M12 is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity...
£3.20
£3.84 inc VAT
Brand: TECO
Model: HG3
Delivery Time: In stock, 1-2 days
Helical Bar Grout is a high performance, non-shrink, non-gassing, thixotropic, cement based grout, suitable for injection with a hand or power applicator. It has a low liquid to powder ratio, which gives the thixotropic ability - the grout would flow sufficiently to form a uniform layer, then to res..
£64.34
£77.21 inc VAT
Brand: TECO
Model: WT-225/50
Delivery Time: In stock, 1-2 days
225mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from 50mm to 70mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000Meets the requirement..
£9.69
£11.63 inc VAT
Brand: TECO
Model: LD800F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 800mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres hol..
£1.39
£1.67 inc VAT